TC1000 ix External Protein Skimmer

Suitable for aquariums up to 1000 lts (220 UK Gallons).

Deltec's innovative TC-PRO (Twin chamber) range of external protein skimmers featuring Deltec's high performance pump with class leading energy to air ratio.

For over 25 years Deltec GMBH have worked hard to develop the best specialist marine aquarium equipment available on the market. They are known throughout the world for the high performance and quality of their protein skimmers. When their patent on the Deltec Pinwheel ran out it opened the market for other people to copy their ideas and to produce pinwheels of their own but without the 25+ years of experience and development that had gone into the Deltec products.

The latest generations of Deltec protein skimmers have been developed to produce the optimum air to water ratio in the reaction chamber for the lowest possible power consumption.

The TC name describes the special Twin Chamber design of the bubble chamber which is patented and has the benefit of pressurising the pumps for higher performance and ensures that only unskimmed water passes through the pump rather than reskimming and reprocessing water in the chamber.

The bubble plate design allows the height of the skimmers to be reduced and allow them to fit in a cabinet. The primary use of the bubble chamber is to prevent turbulence from the skimmer body and neck as turbulence can pull waste loaded bubbles back into the water column causing a reduction in efficiency. The air to water ratio is so high that there is almost immediate reaction with the waste therefore there is no requirement for the tall reaction chambers found on some low air skimmers thus keeping the units compact.

Technical Data

Aquarium Size : 1000 lts (220 UK Gallons)
Height: 535mm
Footprint including pipework: 270mm by 200mm
Height under outlet pipe: 251mm
Total air produced: 600 lts/hour
Power consumption: 12W
Connections: 20mm in 32mm out
Remote drain on skimmer cup.
Air silencer.
Micro adjustable skimmer setting.
Can be gravity or pump fed (supply pump not supplied).
Recommended water supply 1000 ltrs/hr.
Article no 80150000.
Also available with manual cleaning head CSM 1000

FAQs
- Why does the light on the D-D ATO sensor change?
- Why is my D+D ATO sensor light red

FAQs

Why does the light on the D-D ATO sensor change?

The sensor on the DDATO has different light colours and patterns to warn of faults or show its status.

Flashing blue and red LED. The unit has been powered on and it is going through its startup process.

Flashing blue LED. A low water level has been detected and the top up unit is operating the pump to refill with fresh water.

Short intermitting blinking blue LED. The waterlevel is above the failsafe sensor and the unit has been temporarily deactivated. When the water level returns to below the emergncy sensor the unit will return to normal operation. The failsafe sensor can be activated after each top up on nano aquariums, this is normal and no action needs to be taken.

Solid Blue LED. The top up unit is in normal standby mode.

Flashing red LED. Alarm mode has been activated. The unit has detected an issue and or the freshwater reservoir is empty.

Why is my D+D ATO sensor light red

A red light on the sensor can indicate one of these things.

The sensor's inbuilt emergency shut-off timer has been activated

When the unit performs its first top-up after being powered on it will store the time taken in its memory. If for any reason the top-up unit is activated for longer than 6 times this the sensor will assume there is a problem or that the freshwater reservoir is empty, shut down and show the red warning light.

Corrective action to set the ATO back into normal operation mode and clear the alarm status, power the unit down from the mains plug socket for a few seconds and then power it back up. The sensor should flash red/blue a few times as it reinitialises and then returns to normal operation mode with a solid blue status light.

The sensor is detecting a fault with the ATO pump.

If the pump cannot run the sensor may go into alarm mode and turn off power to the pump. If this is the situation you will notice that when the top-up activates the pump will not turn on and the status light will immediately show red and not flash blue until time out occurs.

Corrective action:_Disconnect the unit from mains power, check that the connector where the power lead and pump plug-in has not become wet and that the impellor in the pump is clean and free to move.

The freshwater reservoir is empty or the sensor is impaired

No water in the reservoir or microbubbles in the water are causing issues with the sensor detecting the water level. Check that the sensor is not in an area where it is subject to small bubbles, eg near the outlet from a skimmer.

Corrective action: If this has occurred check that the sensor is clean, the impellor in the pump is clean and free to move, the freshwater reservoir is not empty, and there is nothing that could be causing the sump water level to fall unexpectedly.

Payment Methods

We accept all major Credit and Debit cards, and these are processed via a third party payment gateway called Opayo.

We also accept payments via PayPal and PayPal credit.

Also, you can pay using Android and Apple Pay if you are using a compatible device.

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

Security

When speaking to one of our team, we will never ask you for your bank details, passwords or any private information. We will only ever ask for your order number followed by either your postcode, email address or phone number to verify we are talking to the person named on the account.

When creating an account on our website, we ask that you use a unique password, this will help keep all your online accounts safe. If you are visiting our website via a smartphone we suggest you use the strong password and store it securely on your phone.

Our website is run on Visual Soft, which means all your data is stored securely on their servers.

Next Day Shipping Upgrade - Cut off Midday (12 pm)

Please Note: We only deliver ponds and pond plants on our own delivery vehicles!

The blue highlighted area on the map below is where we deliver on our own vehicle! Unfortunately, if you are not in one of these postcode zones we are unable to deliver certain items such as plants, small glass items and selective other products.

We offer a few different delivery options depending on the size and value of your order.

Orders over £50 qualify for free mainland UK (excludes Northern Ireland) delivery which will arrive within 3-5 working days of the order being processed.

Residents of Northern Ireland, please provide your EORI or XI Number.

If you do not have one, please follow the information at https://www.gov.uk/eori

Orders Below £50 in Mainland UK will be charged a standard delivery fee of £5.99.

Additional Shipping Charges

For any orders that do not include Aquariums, the below is charged:

Next Working Day Parcel Delivery to Mainland UK - £7.99 OR £2.99 if the order is over £50

Standard Parcel Delivery to Northern Ireland £8.99

Standard Parcel Delivery to Scottish Highlands & Islands £9.99

Standard Parcel Delivery to Jersey & Guernsey £12.99

For all Aquarium deliveries (Excluding biOrbs & Smaller Aquariums), the below is charged:

Next Working Day Pallet Delivery - £20

2 Hour Booking Slot Pallet Delivery - £20

Pallet Delivery to Northern Ireland - £38

Pallet Delivery to Isle of Wight (PO36 and Above) and Scottish Highlands (AB, PH, IV1-36, IV63, KW1-14, KY, PA21-41) - £38

Pallet Delivery to Southern Ireland - £48

Pallet Delivery to Offshore postcodes (KA27-28, PA20, PA42-49, PA60-90, ZE, JE, GY. IM) - £70

Pallet Delivery to the Scottish Isles (IV40-56, KW15-17) - £90

Pallet Delivery to Outer Hebrides (HS) - £120

D-D Aquarium Solutions Tc-Pro 1000Ix 230V External Skimmer

Technical Data