This site uses cookies to provide and improve your shopping experience.
If you want to benefit from this improved service, please opt-in.
Cookies Page.
These new pumps improve on the previous DCP pump design as follows:
Sine Wave controller technology provides super quiet operation
New Digital Controller- Speed Control Settings Between 30%-100% in 1 Watt increments
Digital display of power consumption.
Suitable for external and internal operation
Seals for input and output connections
Improved Head Pressure Performance over DCP Models
New Enclosed Impeller Design For a more Quiet Operation
Energy Saving up to 65%
IC Electronic Detection- Automatic Power Off Protection Upon No Water
Wear Resistant Ceramic Shaft
Features
DCP-2500 (23W)
Maximum flow rate of up to 2,500 litres/hour - adjustable from 750 - 2,500 litre/hour
DCP-4000 (33W)
Maximum flow rate of up to 4,000 litres/hour - adjustable from 1,200 - 4,000 litres per hour
DCP-6500 (55W)
Maximum flow rate of up to 6,500 litres/hour - adjustable from 1,950 - 6,000 litres per hour
DCP-8000 (65W)
Maximum flow rate of up to 8,000 litres/hour - adjustable from 2,400 - 8,000 litres per hour
DCP-10000 (80W)
Maximum flow rate of up to 10,000 litres/hour - adjustable from 3,000 - 10,000 litres per hour
DCP-13000 (95W)
Maximum flow rate of up to 13,000 litres/hour - adjustable from 3,900 - 13,000 litres per hour
DCP-15000 (105W)
Maximum flow rate of up to 15,000 litres/hour - adjustable from 4,500 - 15,000 litres per hour
DCP-18000 (145W)
Maximum flow rate of up to 18,000 litres/hour - adjustable from 5,400 - 18,000 litres per hour in
DCP-20000 (170W)
Maximum flow rate of up to 20,000 litres/hour - adjustable from 8,000 - 20,000 litres per hour in
Electronic detection of no water enables automatic power off protection
Motor protection if rotor is blocked
Can be used in Marine and Freshwater applications
No copper elements
Long operation life is achieved by the use of wear resistant ceramic shaft
Soft start operation - pump gradually builds up to set flow rate
Feed mode disables pump for 10 minutes
Speed settings (30% - 100%) in 1Watt steps with power consumption indication - setting is retained if power is lost.
Dimensions
DCP-2500 = 103 x 73 x 98 L x W x H (mm)
DCP-4000 = 158 x 80 x 128 L x W x H (mm)
DCP-6500 = 196 x 104 x 163 L x W x H (mm)
DCP-8000 = 196 x 104 x 163 L x W x H (mm)
DCP-10000 = 196 x 104 x 163 L x W x H (mm)
DCP-13000 = 196 x 104 x 163 L x W x H (mm)
DCP-15000 = 223 x 126 x 192 L x W x H (mm)
DCP-18000 = 223 x 126 x 192 L x W x H (mm)
DCP-20000 = 223 x 126 x 192 L x W x H (mm)
Whats Included
DCP Pump
Sine Wave technology Controller
Power adapter with Uk plug
Connectors for rigid pipe
Hosetail Connectors for flexible tube
Inlet filter
Instructions
Flow Chart
Error codes
Er01: Abnormal Working current; Check if the pump voltage is correct or the controller is broken Er02: Controller overheating; Check whether the controller is exposed to sunshine or in a high-temperature environment Er03: Pump idling; Check if the pump is running dry Er04: The impeller stops running; Check if the pump voltage is correct or the controller is broken Er05: Abnormal Working voltage. Check the input supplying voltage
The sensor on the DDATO has different light colours and patterns to warn of faults or show its status.
Flashing blue and red LED. The unit has been powered on and it is going through its startup process.
Flashing blue LED. A low water level has been detected and the top up unit is operating the pump to refill with fresh water.
Short intermitting blinking blue LED. The waterlevel is above the failsafe sensor and the unit has been temporarily deactivated. When the water level returns to below the emergncy sensor the unit will return to normal operation. The failsafe sensor can be activated after each top up on nano aquariums, this is normal and no action needs to be taken.
Solid Blue LED. The top up unit is in normal standby mode.
Flashing red LED. Alarm mode has been activated. The unit has detected an issue and or the freshwater reservoir is empty.
Why is my D+D ATO sensor light red
A red light on the sensor can indicate one of these things.
The sensor's inbuilt emergency shut-off timer has been activated
When the unit performs its first top-up after being powered on it will store the time taken in its memory. If for any reason the top-up unit is activated for longer than 6 times this the sensor will assume there is a problem or that the freshwater reservoir is empty, shut down and show the red warning light.
Corrective action to set the ATO back into normal operation mode and clear the alarm status, power the unit down from the mains plug socket for a few seconds and then power it back up. The sensor should flash red/blue a few times as it reinitialises and then returns to normal operation mode with a solid blue status light.
The sensor is detecting a fault with the ATO pump.
If the pump cannot run the sensor may go into alarm mode and turn off power to the pump. If this is the situation you will notice that when the top-up activates the pump will not turn on and the status light will immediately show red and not flash blue until time out occurs.
Corrective action:_Disconnect the unit from mains power, check that the connector where the power lead and pump plug-in has not become wet and that the impellor in the pump is clean and free to move.
The freshwater reservoir is empty or the sensor is impaired
No water in the reservoir or microbubbles in the water are causing issues with the sensor detecting the water level. Check that the sensor is not in an area where it is subject to small bubbles, eg near the outlet from a skimmer.
Corrective action: If this has occurred check that the sensor is clean, the impellor in the pump is clean and free to move, the freshwater reservoir is not empty, and there is nothing that could be causing the sump water level to fall unexpectedly.
Can it be mounted on suction cups and are there cut outs on the filter case to install these by?
No, the M Bioflow does not have any suction cups to hold the filter to the aquarium. There are no holes on the filter designed to hold such suction clips.
Payment Methods
We accept all major Credit and Debit cards, and these are processed via a third party payment gateway called Opayo.
We also accept payments via PayPal, PayPal credit, Clearpay and Klarna which are both pay in 4 interest-free instalments.
Also, you can pay using Android and Apple Pay if you are using a compatible device.
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
Security
When speaking to one of our team, we will never ask you for your bank details, passwords or any private information. We will only ever ask for your order number followed by either your postcode, email address or phone number to verify we are talking to the person named on the account.
When creating an account on our website, we ask that you use a unique password, this will help keep all your online accounts safe. If you are visiting our website via a smartphone we suggest you use the strong password and store it securely on your phone.
Our website is run on Visual Soft, which means all your data is stored securely on their servers.
Next Day Shipping cut off is at Noon/12:00pm
Orders after that time will be processed the next working day
Please Note: Certain ponds, aquariums, all pond plants, and all livestock are excluded from free delivery.
The blue highlighted area on the map below is where we deliver on our own vehicle. Unfortunately, if you are not in one of these postcode zones we are unable to deliver certain items such as plants, small glass items and selective other products.
We offer a few different delivery options depending on the size and value of your order.
Certain orders over £50 qualify for free mainland UK (excludes Northern Ireland, Pond Plants, and livestock) delivery which will arrive within 3-5 working days of the order being processed.
Orders Below £50 in Mainland UK will be charged a standard delivery fee of £5.99.
Pond Plant and Tropical/Marine/Pond Livestock will be charged a delivery fee of £19.99.
Additional Shipping Charges
For any orders that do not include Aquariums, the below is charged:
Next Working Day Parcel Delivery to Mainland UK - £7.99 OR £2.99 if the order is over £50 (excludes Northern Ireland)
Standard Parcel Delivery to Northern Ireland £8.99
Standard Parcel Delivery to Scottish Highlands & Islands £9.99
Standard Parcel Delivery to Jersey & Guernsey £12.99
For all Aquarium, Medium - Extra Large Terrarium/Vivarium/Paludarium deliveries (Excluding biOrbs & Smaller Aquariums), the below is charged:
You must be present for delivery and please check your item before signing for delivery.
A payment link will be sent to you if redelivery is required.
Next Working Day Pallet Delivery - £20
2 Hour Booking Slot Pallet Delivery - £20
Pallet Delivery to Northern Ireland - £45
Saturday and OptiClear 90 & 120 Delivery - £60
Pallet Delivery to Isle of Wight (PO30 and Above) and Scottish Highlands (AB, PH, IV1-36, IV, KW1-14, KY, PA21-41) - £45
Pallet Delivery to the Scottish Isles (KA27-28, PA60-90, ZE, JE, GY, IM, IV40-56, KW15-17, PH42-44, PA20, PA42-49) - £120
Pallet Delivery to Outer Hebrides (HS) - £140
Pond's over 1000 litres will be a curb side pallet delivery.
Aquariums over 125 litre will be a curb side pallet delivery.