New to 2021, the D-D range of pure titanium heaters is available in four new sizes to suit all marine, reef and freshwater aquariums.
D-D Titanium Heaters
New to 2021, the D-D range of pure titanium heaters available in four new sizes to suit all marine, reef and freshwater aquariums.
D-D Titanium Heaters are manufactured in Germany from high-quality components and are shatterproof, saltwater proof and virtually indestructible, a high-quality product, built to last. These heaters are fully submersible and feature a continuous titanium jacket, thanks to the newly designed internal earth connection.
Titanium is completely non-corrosive in saltwater and one of the best conductors, delivering heat to aquarium water substantially better than conventional glass heaters, for more efficient running.
150 W 250 mm x 25 mm (L x W) For aquariums up to 150 litres
250 W 250 mm x 25 mm (L x W) For aquariums up to 250 litres
350 W 250 mm x 25 mm (L x W) For aquariums up to 350 litres
650 W 350 mm x 25 mm (L x W) For aquariums up to 650 litres
Suction Cap Material: Neoprene
Cable length: 1.5 m
Electrical connection: UK Plug 230 V 50 Hz
NOTE: D-D Titanium Heaters do NOT have a thermostat and therefore require a suitable temperature controller such as the TC125 to regulate temperature.
|Cable Length||1.5 m|
|Aquarium max water||350 l|
|Dimensions||250 mm x 25 mm|
The sensor on the DDATO has different light colours and patterns to warn of faults or show its status.
Flashing blue and red LED. The unit has been powered on and it is going through its startup process.
Flashing blue LED. A low water level has been detected and the top up unit is operating the pump to refill with fresh water.
Short intermitting blinking blue LED. The waterlevel is above the failsafe sensor and the unit has been temporarily deactivated. When the water level returns to below the emergncy sensor the unit will return to normal operation. The failsafe sensor can be activated after each top up on nano aquariums, this is normal and no action needs to be taken.
Solid Blue LED. The top up unit is in normal standby mode.
Flashing red LED. Alarm mode has been activated. The unit has detected an issue and or the freshwater reservoir is empty.
A red light on the sensor can indicate one of these things.
The sensor's inbuilt emergency shut-off timer has been activated
When the unit performs its first top-up after being powered on it will store the time taken in its memory. If for any reason the top-up unit is activated for longer than 6 times this the sensor will assume there is a problem or that the freshwater reservoir is empty, shut down and show the red warning light.
Corrective action to set the ATO back into normal operation mode and clear the alarm status, power the unit down from the mains plug socket for a few seconds and then power it back up. The sensor should flash red/blue a few times as it reinitialises and then returns to normal operation mode with a solid blue status light.
The sensor is detecting a fault with the ATO pump.
If the pump cannot run the sensor may go into alarm mode and turn off power to the pump. If this is the situation you will notice that when the top-up activates the pump will not turn on and the status light will immediately show red and not flash blue until time out occurs.
Corrective action:_Disconnect the unit from mains power, check that the connector where the power lead and pump plug-in has not become wet and that the impellor in the pump is clean and free to move.
The freshwater reservoir is empty or the sensor is impaired
No water in the reservoir or microbubbles in the water are causing issues with the sensor detecting the water level. Check that the sensor is not in an area where it is subject to small bubbles, eg near the outlet from a skimmer.
Corrective action: If this has occurred check that the sensor is clean, the impellor in the pump is clean and free to move, the freshwater reservoir is not empty, and there is nothing that could be causing the sump water level to fall unexpectedly.
A heater in a fish tank is used to maintain a consistent, appropriate water temperature for the fish and other aquatic life living in the tank. Different species of fish have different temperature requirements, so it's important to ensure that the water temperature in the tank is within the appropriate range for the specific type of fish you are keeping.
In general, most tropical fish need a water temperature in the range of 24-28 degrees Celsius. Coldwater fish, such as goldfish, may prefer water that is slightly cooler, around 20-23 degrees Celsius.
A heater in a fish tank helps to maintain a stable water temperature by using an electric heating element to warm the water. The heater is typically placed inside the tank and connected to a thermostat that measures the water temperature and turns the heater on or off as needed to maintain the desired temperature.
It's important to monitor the water temperature in your fish tank regularly and to adjust the heater as needed to ensure that the temperature stays within the appropriate range for your fish. If the water temperature gets too cold, the fish may become sluggish and inactive, and may be more prone to illness. On the other hand, if the water temperature gets too hot, the fish may become stressed and may also be more prone to illness.
We accept all major Credit and Debit cards, and these are processed via a third party payment gateway called Opayo.
We also accept payments via PayPal and PayPal credit.
Also, you can pay using Android and Apple Pay if you are using a compatible device.
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
When speaking to one of our team, we will never ask you for your bank details, passwords or any private information. We will only ever ask for your order number followed by either your postcode, email address or phone number to verify we are talking to the person named on the account.
When creating an account on our website, we ask that you use a unique password, this will help keep all your online accounts safe. If you are visiting our website via a smartphone we suggest you use the strong password and store it securely on your phone.
Our website is run on Visual Soft, which means all your data is stored securely on their servers.
Next Day Shipping Upgrade - Cut off Midday (12 pm)
Please Note: We only deliver ponds and pond plants on our own delivery vehicles!
The blue highlighted area on the map below is where we deliver on our own vehicle! Unfortunately, if you are not in one of these postcode zones we are unable to deliver certain items such as plants, small glass items and selective other products.
We offer a few different delivery options depending on the size and value of your order.
Orders over £50 qualify for free mainland UK (excludes Northern Ireland) delivery which will arrive within 3-5 working days of the order being processed.
Residents of Northern Ireland, please provide your EORI or XI Number.
If you do not have one, please follow the information at https://www.gov.uk/eori
Orders Below £50 in Mainland UK will be charged a standard delivery fee of £5.99.
Additional Shipping Charges
For any orders that do not include Aquariums, the below is charged:
Next Working Day Parcel Delivery to Mainland UK - £7.99 OR £2.99 if the order is over £50
Standard Parcel Delivery to Northern Ireland £8.99
Standard Parcel Delivery to Scottish Highlands & Islands £9.99
Standard Parcel Delivery to Jersey & Guernsey £12.99
For all Aquarium deliveries (Excluding biOrbs & Smaller Aquariums), the below is charged:
Next Working Day Pallet Delivery - £20
2 Hour Booking Slot Pallet Delivery - £20
Pallet Delivery to Northern Ireland - £38
Pallet Delivery to Isle of Wight (PO36 and Above) and Scottish Highlands (AB, PH, IV1-36, IV63, KW1-14, KY, PA21-41) - £38
Pallet Delivery to Southern Ireland - £48
Pallet Delivery to Offshore postcodes (KA27-28, PA20, PA42-49, PA60-90, ZE, JE, GY. IM) - £70
Pallet Delivery to the Scottish Isles (IV40-56, KW15-17) - £90
Pallet Delivery to Outer Hebrides (HS) - £120